Toshiba IK-DF02A Uživatelský manuál

INSTRUCTION MANUALDOME CAMERA ZEIM-4000100G A.1IK-DF02ATABLE OF CONTENTS IMPORTANT SAFEGUARDS... 11. FEATU

- 9 -UpsideTo Determine Which Set of Mounting Holes to UseMounting Holes (i)• Installation to a wall or ceiling.(Refer to section 5-1-2.)• Installatio

- 10 -5-1-2. Installation to a Wall or CeilingTo mount the camera directly on thewall or ceiling.1. Prepare the mounting space.2. Place the camera on

- 11 -B: Routing the Wires to the Left Side1. Remove the wires from the wirehole and position them to the leftof the base.2. Firmly secure the wires w

- 12 -1.81(46)Dimensions: inch (mm)3.29(83.5)Upside5-1-3. Installation to a Switch Box(i) Mounting the Camera to a Switch Box Positioned Normally on a

- 13 -1.81(46)Dimensions: inch (mm)3.29(83.5)Upside(ii) Mounting the Camera to a Switch Box Positioned Sideways1. Install the switch box positioned si

- 14 -(iii) Mounting the Camera to a Switch Box Attached to a Ceiling1. Position the cover to conceal theunlock-button from the visible side.2. Use th

- 15 -5-2. Adjusting the Viewing Angle(1) To check the video image on the monitor, connect the "Monitor Out Harness Wire" to theconnector &q

- 16 -7. LINE LOCK PHASEIf two or more cameras within a system have different AC line phases and they are switched bya video switcher, the picture on

- 17 -8. NOTES ON USE AND INSTALLATION• Do not aim the camera at the sunNever aim the camera at the sun even with the camera power off.• Do not shoot

- 18 -9. IN CASE OF PROBLEMSConditionNo imageUnnatural colorThe image is out offocus.The image is dark.Check Points• Are the camera and connected equi

- 1 -1. Read InstructionsAll the safety and operating instructions should beread before the product is operated.2. Retain InstructionsThe safety instr

- 19 -1. Image SystemImage DevicePixel Elements2. ElectricalTV SystemHorizontal ResolutionS/N RatioMinimum IlluminationAuto Gain Control (AGC)Iris Con

- 20 -11. EXTERIOR VIEW1.81 (46)(1.81 (46))2.05 (52)0.05 (1.2)3.94 (100)3.99 (101.2)3.29 (83.5)(3.29 (83.5))Dimensions: inch (mm)5.08 (129)5.08 (129)

- 21 -1.81 (46)1.81 (46)3.94 (100)depth about 1.58 (40)3.29 (83.5)Dimensions: inch (mm)Screw ( 0.18 (4)) x4 - TP4 x37Wall

- 22 -MEMO

LIMITED WARRANTYCCD SECURITY CAMERA IK-DF02AThe Imaging System Division ("ISD") of Toshiba America Information Systems, Inc. makes the follo

- 2 -• The CAUTION label, shown on the left,is attached on the camera.CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK.DO NOT REMOVE COVER (OR BACK).NO US

- 3 -DisclaimerWe disclaim any responsibility and shall be held harmless for any damages or losses incurred bythe user in any of the following cases:1

- 4 -1. FEATURES AND DESCRIPTION1. 24V AC/12V DC dual-voltage capability extends power options.2. Camera has the ability to automatically switch to co

- 5 -1ONOFF2343. PART NAMES AND FUNCTIONSPan ADJ ScrewTurn the ring-type screw toadjust the lens pan angle.Fasten and lock it aftercompleting the adju

- 6 -4. CONNECTIONS•Power plugs of connected equipment must be disconnected before camerainstallation.•A 75-ohm coaxial cable with connector (3C-2V or

- 7 -4-2. Line lock Control• Matching the vertical synchronization with the power frequency is called the Line Lock.•To activate the line lock, set th

- 8 -UpsideP5. INSTALLATIONNote: The attached screws are used to install the camera to a solid surface. If installing to surfacesof loose or thin mate