Toshiba IK - TU51CU Uživatelský manuál

TOSHIBAINSTRUCTION MANUALCAMERA CONTROL UNITIK-TU51 euFor Customer UseEnter below the Serial No. which is located on the bottom of the cabi

5. CONNECTION5. 1 Standard ConnectionLensCamera cable(option)Camera head (option)IK-TU51CUCamera Control unitCoaxialVIDEO Cable 75 QDC IN 12VDC power

5. 3A Connector Pin AssignmentsDC IN 12VDC IN/SYNC1 +12V2+12V3GND4 GNDDIGITAL1 GND2 +12V3GND(for INDEX)4 INDEX5GND(for HD)6HD OUT7 VD OUT8GND(for TRIG

6. OPERATION(i) Referring to the item “ 5. CONNECTION”, connect each equipment correctly.(D Turn on the connected equipment and the camera.(D When usi

6. 2 White BalanceFor the white balance adjustment for this unit, ATW (Automatic Trace White balance), AWB (Automatic White Balance) and M

DisplayMeaningAWB OK Automatic white balance adjustment finished correctly.AWB NG LEVEL LOWAutomatic white balance adjustment cannot be performed beca

6. 3 Scene FileThree scene files (A, B, C) are available as user memories for this unit. These are selectable depending on shooting conditions. By

6. 5 Shading CorrectionDue to the lens used or the environmental condition, color shading may occur at the upper and lower side of the screen. In this

6. 6 Freeze OperationFreeze Mode Operation is only possible when no menu character display or color bar is on the screen. Freeze Mode Operation is not

i18

7. 2 Menus• Select the menu to change the setting by referring the item “7.1 Using the Menus”.)• When the [MENU UP], [MENU DOWN] buttons are pushed, t

SAFETY PRECAUTIONSRead the following safety precautions carefully before using the product. These instructions contain valuable Information on safe an

(1.1) Changing each setting in AUTO mode• Shutter mode AUTO, MANUAL, SS, EXT TRIG• Video level adjustment -100 to 100 Peak and average ratio adjustm

(d) Changing the automatic shutter zone area0 Set the ” to AREA by pushing [MENU UP], [MENU DOWN] buttons.(D Set the measurement light area by pushin

(1. 2) Changing each setting in MANU mode• Sutter mode AUTO, MANUAL, SS, EXT TRIG - • Sutter speed settingOFF, 1/100S, 1/250S, 1/500S, 1/1000S, 1/2000

(1. 3) Changing each setting in SS (synchro, scan) mode- • Shutter mode AUTO, MANUAL, SS, EXT TRIG' • Synchro, scan setting1 /525H-^260/525H-^OFF

(1. 4) Changing each setting in EXT TRIG modeThe EXT TRIG has four modes; 1 PULSE SNR, 1 PULSE SR, 2PULSE, RS232C.First set the to MODE and sele

(1. 4. 2) Changing each setting in 1 PULSE SR mode• Shutter mode AUTO. MANUAL, SS, EXT TRIO• EXT TRIG mode1 PULSE SNR. 1 PULSE SR. 2PULSE. RS232C• Inp

(1. 4. 3) Changing each setting in 2PULSE mode. • Shutter mode AUTO, MANUAL, SS, EXT TRIG• EXT TRIG mode1 PULSE SNR, 1 PULSE SR, 2PULSE, RS232C• Input

(1. 4. 4) Changing each setting in RS232C mode• Sutter mode AUTO, MANUAL, SS, EXT TRIG• EXT TRIG mode1 PULSE SNR, 1 PULSE SR, 2PULSE, RS232C• FLD/FRM

(2. 1) Changing the maximum gain in AUTO (Automatic gain control) mode• Gain mode AUTO, MANUAL, OFF• Automatic maximum gain setting OdB to 20dB(1 dB s

(3) WHT BALfWhite balancedThe WHT BAL has three modes; AWB, ATW, MANUAL.Set the to MODE, push the [DATA UP], [DATA DOWN], and select mode among AWB,

Keep the followings when installing.• Do not put the product on a Inflammable material such as carpet or blanket.• Do not put the product in a narro

PRESET APRESET EPRESET BPRESET CPRESET DCustomSelectionUSER(e) Confirming the contents of the zone area0 Set the to AREA DISP by pushing [MENU UP], [

(b) Changing B PAINT0 Set the ” to B PAINT by pushing [MENU UP], [MENU DOWN] buttons. (D Set the blue paint by pushing [DATA UP], [DATA DOWN] buttons.

(4) PROCESSMove up and down By pushing MENU UP,DOWN-- 4 PROCESS-GAMMA ON/OFF GAMMABLACK GAMMA 2D LPF DTL GAIN DTL B. FRQ M. PED CHROMA GAIN DNRGamma

(4. 3) Changing black gamma correction level® Set the to BLACK GAMMA by pushing [MENU UP], [MENU DOWN] buttons. (2) Select black gamma correction by p

(4. 7) Changing master pedestal® Set the to M. PED by pushing [MENU UP], [MENU DOWN] buttons.(D Set the master pedestal by pushing [DATA UP], [DATA DO

(5) MATRIX(Matrix color correction) Red hue setting Red gain setting’ Green hue setting • Green gain setting Blue hue setting Blue gain settingM

(6) SYNCWhen an external sync signal is input, the display changes from INT (internal sync) to EXT (external sync) automatically.INT^-------► EXT(6. 1

(7) OPTION/• OUTPUT1 RGB, Y/PR/PB• OUTPUT2 VBS, Y/C• SHADING MODE SET, MANUAL, OFF, • Manual shading setting -128 to 127^ • RGB SYNC G, ALL ON, ALL OF

(7. 6) Changing FREEZE DISP setting® Set the to FREEZE DISP by pushing [MENU UP], [MENU DOWN] buttons.(D Select either ON or OFF by pushing [DATA UP],

(D Move the “o" to the zone to be appeared.The display “o" moves up, down, left and right by pushing [MENU UP], [MENU DOWN], [D

TABLE OF CONTENTS1. CAUTIONS ON USE AND INSTALLATION... 62. COMPONENTS...

(9) Setting to factory setting statusThe contents set of each scene file can be returned to the factory default status (preset status).(1) Select a fi

(2) External svnc frequency range(External sync with VBS, SYNC)For NTSC standard frequency : Within ±50ppm (External sync with HD, VD)For EIA standar

7. 4 Synchro. Scan OperationThe shutter speed can be set by the horizontal scanning period (1H) or by the frame. Also, CCD integration mode can be set

7. 5 EXT TRIG (External trigger)Charge begins to accumulate after the trigger Input operation (In the RS232C mode, by RS232C command Input, In other m

(2) 1 PULSE SR (1 Pulse Svnc Reset)Charge begins to accumulate after the trigger input operation to the DC IN/SYNC terminal or trigger signal input (

(3) 2PULSEAccumulation of charges Is started and ended through the trigger pulse input to the DC IN/SYNC terminal or trigger signal input (LVDS) to

(Frame storage period)TRIGGER ))( Pulse width mode(DC IN/SYNC terminal)or , TRIGGER D (DIGITAL terminal)dnr_| Falling edge mode ^ Rising edge mode^

(4) RS232CAccumulation of charges is started and ended through RS232C commands to the DIGITAL terminal, the vertical sync signal is reset and field I

7. 6 Freeze Operation by Trigger InputWhen the shutter mcxJe is set to AUTO, MANUAL or SS and the shutter menu’s FREEZE INPUT setting is set to TRIG

7. 7 Digital outputThis unit outputs 10 bit digital video signals each for R, G and B from the DIGITAL terminal using the LVDS (Low Voltage Differenti

(7) OPTION... 37(7.1) Chaging OUTP

8. BEFORE MAKING SERVICE CALLSymptomItems to be checkedNo picture• Is the power supplied correctly?• Is the lens iris adjusted correctly?• Are the

9. SPECIFICATIONSPower supplyDC12V±10%Power consumptionApprox. 7.8W (including a camera head)Pick-up systemRGB, 3CCD, Micro prism systemAvailable Ima

10. EXTERNAL APPEARANCE DIAGRAMUnit: mm [inch]110 15652

LIMITED WARRANTY CCD CAMERAThe Imaging Systems Division of Toshiba America Information Systems, Inc. (“ISD”) makes the following limited warranties wi

1. CAUTIONS ON USE AND INSTALLATION•Carefully handle the units.Do not drop, or give a strong shock or vibration to the camera. This may cause p

3. ITEMS CONTROLLED BY USING ON SCREEN DISPLAYItemAvailable selectionsPreset vaiue (Factory setting)MODEAUTO. MANUAL, SS, EXT TRIGMANUALEXT TRIG1 PUL

ItemAvailable selectionsPreset value (Factory setting)Ext.Sync.H phase adjustment-100 - 0 - 1000SC 0/180 0. 180 0SC phase adjustment-128 - 0 - 1270OUT

©Camera cable terminal ©POWER LED ©POWER switch 0FILE button ©FREEZE button©DISP button ©PAGE button ©MENU UP(SHD)button©MENU DOWN button ©DATA UP(AWB